Complexity in Consumer Electronics Considered Harmful
I recently returned from a visit to my grandmother, who lives in an assisted living community, and got to observe both her and my frustration first-hand with a new TV. This was a Vizio flatscreen TV that was fairly easy to set up, and the picture quality was good. But here's what the remote control looks like:
You will note:
- the small lettering (the number buttons are just under 1/4 inch in diameter)
- a typeface chosen for marketing purposes (matching Vizio's "futuristic" corporate...
Which MOSFET topology?
A recent electronics.StackExchange question brings up a good topic for discussion. Let's say you have a power supply and a 2-wire load you want to be able to switch on and off from the power supply using a MOSFET. How do you choose which circuit topology to choose? You basically have four options, shown below:
From left to right, these are:
High-side switch, N-channel MOSFET High-side switch, P-channel MOSFET Low-side switch, N-channel...Thermistor signal conditioning: Dos and Don'ts, Tips and Tricks
In an earlier blog entry, I mentioned this circuit for thermistor signal conditioning:
It is worth a little more explanation on thermistor signal conditioning; it's something that's often done poorly, whereas it's among the easiest applications for signal conditioning.
The basic premise here is that there are two resistors in a voltage divider: Rth is the thermistor, and Rref is a reference resistor. Here Rref is either R3 alone, or R3 || R4, depending on the gain...
Real-time clocks: Does anybody really know what time it is?
We recently started writing software to make use of a real-time clock IC, and found to our chagrin that the chip was missing a rather useful function, namely elapsed time in seconds since the standard epoch (January 1, 1970, midnight UTC).Let me back up a second.A real-time clock/calendar (RTC) is a micropower chip that has an oscillator on it that keeps counting time, independent of main system power. Usually this is done with a lithium battery that can power the RTC for years, so that even...
Byte and Switch (Part 2)
In part 1 we talked about the use of a MOSFET for a power switch. Here's a different circuit that also uses a MOSFET, this time as a switch for signals:
We have a thermistor Rth that is located somewhere in an assembly, that connects to a circuit board. This acts as a variable resistor that changes with temperature. If we use it in a voltage divider, the midpoint of the voltage divider has a voltage that depends on temperature. Resistors R3 and R4 form our reference resistance; when...
Byte and Switch (Part 1)
Imagine for a minute you have an electromagnet, and a microcontroller, and you want to use the microcontroller to turn the electromagnet on and off. Sounds pretty typical, right?We ask this question on our interviews of entry-level electrical engineers: what do you put between the microcontroller and the electromagnet?We used to think this kind of question was too easy, but there are a surprising number of subtleties here (and maybe a surprising number of job candidates that were missing...
April is Oscilloscope Month: In Which We Discover Agilent Offers Us a Happy Deal and a Sad Name
Last month I wrote that March is Oscilloscope Month, because Agilent had a deal on the MSOX2000 and MSOX3000 series scopes offering higher bandwidth at lower prices. I got an MSOX3034 oscilloscope and saved my company $3500! (Or rather, I didn't save them anything, but I got a 350MHz scope at a 200MHz price.)
The scope included a free 30-day trial for each of the application software modules. I used my 30-day trial for the serial decode + triggering module, to help debug some UART...
Short Takes (EE Shanty): What shall we do with a zero-ohm resistor?
In circuit board design you often need flexibility. It can cost hundreds or thousands of dollars to respin a circuit board, so I need flexibility for two main reasons:
- sometimes it's important to be able to use one circuit board design to serve more than one purpose
- risk reduction: I want to give myself the option to add in or leave out certain things when I'm not 100% sure I'll need them.
And so we have jumpers and DIP switches and zero-ohm resistors:
Jumpers and...
The Art of Debugging
Debugging electronics is similar to any technological process. In theory we know how things are supposed to work, in reality they don't behave as expected. The challenge of engineering boils down to making things work, and debugging is the fundamental task we use to go from lumps of sand to picosecond accurate switching networks. Debugging is an art that requires a lot of time to learn. Like any skill, the more we work at it, the better we become.
The first...
Working of the first solid state amplifier
Whenever a circuit designer thinks about amplifier, the first think that pops up in his mind is that of operational amplifier (Op-Amp). The answer is simple op-amps are beautiful (literally), you just have to set the gain of the op-amps with pair of resistors and you are good to go.
3 LEDs powered by fingers - puzzle
I would like to present my last puzzle design.
If you like such puzzles, I invite you to watch the movie below.
How does it work ?
3 LEDs powered by fingers - puzzle
I would like to present my last puzzle design.
If you like such puzzles, I invite you to watch the movie below.
How does it work ?
Modeling Gate Drive Diodes
This is a short article about how to analyze the diode in some gate drive circuits when figuring out turn-off characteristics --- specifically, determining the relationship between gate drive current and gate voltage during turn-off of a power transistor.
The Art of Debugging
Debugging electronics is similar to any technological process. In theory we know how things are supposed to work, in reality they don't behave as expected. The challenge of engineering boils down to making things work, and debugging is the fundamental task we use to go from lumps of sand to picosecond accurate switching networks. Debugging is an art that requires a lot of time to learn. Like any skill, the more we work at it, the better we become.
The first...
Working of the first solid state amplifier
Whenever a circuit designer thinks about amplifier, the first think that pops up in his mind is that of operational amplifier (Op-Amp). The answer is simple op-amps are beautiful (literally), you just have to set the gain of the op-amps with pair of resistors and you are good to go.
